en:sim:manual:jak_na_instalaci:stridace
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verze | ||
en:sim:manual:jak_na_instalaci:stridace [2018/05/25 15:35] – ondra | en:sim:manual:jak_na_instalaci:stridace [2019/09/30 11:52] (aktuální) – ppodhajska | ||
---|---|---|---|
Řádek 9: | Řádek 9: | ||
\\ | \\ | ||
\\ | \\ | ||
- | Terminals SM2-MU: A, B, 4GND, Z, Y, or DC+ a DC - are used according to the inverter manufacturer. </ | + | Terminals SM2-MU: A, B, SGND, Z, Y, or DC+ a DC - are used according to the inverter manufacturer. </ |
\\ | \\ | ||
</ | </ | ||
Řádek 15: | Řádek 15: | ||
If there is SM at the beginning of H-bus, sliding switches must be in ON position.\\ | If there is SM at the beginning of H-bus, sliding switches must be in ON position.\\ | ||
\\ | \\ | ||
- | {{ | + | {{ |
The same for the inverter - if it supports bus termination, | The same for the inverter - if it supports bus termination, | ||
- | If there is manual address scheme in your inverters, you need to set up addresses, ideally beginning with address 1. E.g. 21: 1, 2, 3, …, 31. Procedure is described in inverter' | + | If there is manual address scheme in your inverters, you need to set up addresses, ideally beginning with address 1. E.g. 21: 1, 2, 3, …, 31. Procedure is described in inverter' |
- | ^ SM2-MU | + | ^ SM2-MU |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
|Carlo Gavazzi | - | - | 5(GND) | |Carlo Gavazzi | - | - | 5(GND) | ||
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
- | |GreenBonO) | - | - | - | B(-) | A(+) | - | - | - | - | 9600 | | + | |GreenBonO | - | - | - | B(-) | A(+) | - | - | - | - | 9600 | |
- | |[[.: | + | |[[: |
|KOSTAL | - | - | 3 | 2 | 1 | - | - | ✔ | ✔ | 19200 | | |KOSTAL | - | - | 3 | 2 | 1 | - | - | ✔ | ✔ | 19200 | | ||
|Mastervolt |- | - | - | 3 | 4 | - | - | ✔ | - | 9600 | | |Mastervolt |- | - | - | 3 | 4 | - | - | ✔ | - | 9600 | | ||
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
|Refusol | - | - | - | 3 | 2 | - | - | ✔ | ✔ | 57600 | | |Refusol | - | - | - | 3 | 2 | - | - | ✔ | ✔ | 57600 | | ||
|Santerno |- | - | - | S- |S+ | - | - | ✔ | - | optional | |Santerno |- | - | - | S- |S+ | - | - | ✔ | - | optional | ||
- | |[[.: | + | |[[: |
|Siemens | - | - | - | B | A | - | - | ✔ | ✔ | optional | |Siemens | - | - | - | B | A | - | - | ✔ | ✔ | optional | ||
|Siliken | - | - | 5(GND) | |Siliken | - | - | 5(GND) | ||
- | |[[.:sma|SMA]] | - | - | 5 | 7 | 2 | - | - | ✔ | - | 1200 | | + | |[[: |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
- | |[[.: | + | |[[: |
|Vacon | - | - | 5 | 3 | 4 | - | - | ✔ | ✔ | optional | |Vacon | - | - | 5 | 3 | 4 | - | - | ✔ | ✔ | optional | ||
|Xantrex (GT100-630E) | - | - | GND | RxTx- | RxTx+ | - | - | ✘ | optional | |Xantrex (GT100-630E) | - | - | GND | RxTx- | RxTx+ | - | - | ✘ | optional | ||
Řádek 52: | Řádek 52: | ||
\\ | \\ | ||
- | |||
en/sim/manual/jak_na_instalaci/stridace.txt · Poslední úprava: 2019/09/30 11:52 autor: ppodhajska