en:sim:manual:rozsirujici_moduly:sm2_di
no way to compare when less than two revisions
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Předchozí verzeNásledující verze | |||
— | en:sim:manual:rozsirujici_moduly:sm2_di [2016/11/15 15:54] – ondra | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
+ | ===== SM2-DI ===== | ||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | DI module increases the number of unit's digital inputs significantly and enables connecting other devices.\\ | ||
+ | \\ | ||
+ | **Connecting digital inputs** \\ | ||
+ | \\ | ||
+ | Module SM2-DI has 10 digital inputs. Digital inputs DI can be connected in the same way as inputs to SM2-MU. You can easily connect movement sensor, surge, optical barrier, door sensor and other devices that use contact output to indicate its status.\\ | ||
+ | \\ | ||
+ | There are two ways of wiring.\\ | ||
+ | \\ | ||
+ | The first one requires connecting terminal DC- to SM2-MU with relevant terminal DCOM at the module SM2-DI. One terminal DCOM goes with inputs DI1–DI5 and the second terminal with inputs DI6–DI10. In order to start the input, signal DC+ from SM2-MU unit has to be connected to relevant terminal of SM2-DI terminal.\\ | ||
+ | \\ | ||
+ | {{ .: | ||
+ | \\ | ||
+ | For the second type of wiring, where inputs of SM2-DI module use external power supply (see the following picture), voltage has to be in the range of 8-80 V.\\ | ||
+ | \\ | ||
+ | {{ .: | ||
+ | \\ | ||
+ | **Start and configuration** \\ | ||
+ | \\ | ||
+ | When you have connected the modules and Solar Monitor unit has been connected to the power supply, green LED diode indicating status should glow. If it doesn' | ||
+ | |||
+ | |||
+ | Open menu “System set up/ Inputs and Outputs” in your browser. | ||
+ | |||
+ | |||
+ | Select limit values for relevant connected inputs.\\ | ||
+ | \\ | ||
+ | {{ .: | ||
+ | Tick the box to choose the type of message (e-mail, SMS) that informs the user of changes in input values.\\ | ||
+ | \\ | ||
+ | {{ .: | ||
+ | \\ | ||
+ | ==== Technical specification ==== | ||
+ | <WRAP half column> | ||
+ | ^Binary inputs | 2 x 5 inputs with standard Vcc and GND | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Terminals | max diameter 1.5 mm? | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Connectivity | HBUS | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Dimensions | 35.6 x 89.7 x 62.2 mm | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Installation | DIN rail | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Power supply | 12 – 24 V DC, max 100 mA | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Temperature range | -25 °C to +60 °C | | ||
+ | </ | ||
+ | <WRAP half column> | ||
+ | {{ .: | ||
+ | </ |
en/sim/manual/rozsirujici_moduly/sm2_di.txt · Poslední úprava: 2018/06/25 13:43 autor: ondra