Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.

--- en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu [2018/07/10 13:43] – ondra
+++ en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu [2019/03/11 14:50] (aktuální) – ondra
@@ Řádek 1: / Řádek 1: @@
-===== How to Setup Reading Pulses from the Electrometer =====
+===== Step 4 - Counter Settings =====
@@ Řádek 5: / Řádek 5: @@
-In case there is no electro meter connected to your Solar Monitor, go to [[:en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu|Next >>]]\\
+If there is no counter connected to your Solar Monitor (electrometer, gas meter, inverter, tracker, batery or another meter), go to [[:en:sim:manual:rychly_navod:konfigurace:emaily_sms|Next >>]]\\
 \\
-<WRAP half column>\\
+{{  :en:sim:manual:rychly_navod:konfigurace:krok4.png?direct&  }}\\
+First you need to allow the chosen input, then you will be able to set it up.\\
+{{  :en:sim:manual:rychly_navod:konfigurace:krok4a.png?direct&  }}\\
+Select particular counter.\\
+{{  :en:sim:manual:rychly_navod:konfigurace:krok4b.png?direct&  }}\\
 \\
-\\
+<WRAP info>
-\\
+For details about this settings see chapter [[..:..:menu_nastaveni:vstupy_a_vystupy|Inputs & Counters]].
-\\
+</WRAP>
-In SM2-MU web interface go to menu Settings/Inputs & Counters </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:stridace_a_mereni.png?100  }} </WRAP>\\
+Click on Next on the right to get to the next step. <WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:emaily_sms|Next >>]] </WRAP> <WRAP left> [[:en:sim:manual:rychly_navod:konfigurace:detekce_senzoru|<< Back]] </WRAP>
-For input with a connected meter select option Counter in table Inputs and Counters. Meter can be connected to all 3 inputs. You can connect up to 3 meters to SM2-MU.\\
-{{  :en:sim:manual:rychly_navod:jak_na_to:vstupy_a_citace.png?direct&  }}\\
-<WRAP half column>\\
-In upper part of the table there is name of the counter. Enter its name (e.g. electro meter) and select its type. Set up correct number of pulses per 1 kWh (as stated in SO output parameters at the counter).\\
-</WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:pulzy.png?direct&400  }}\\
-</WRAP> <WRAP half column>\\
-\\
-Enter counter status (e.g. total production at production electro meter). </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:vykon_a_korekce.png?direct&400  }}\\
-</WRAP>\\
-<WRAP info> Default setting  reads 1000 pulses per 1 kWh. If your electro meter shows a different number, change the setting. If it is 1000 pulses, go to [[:en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu|Next >>]]. </WRAP> <WRAP half column> </WRAP> <WRAP half column>\\
-The number of impulses per 1 kWh is usually between 250-1000 imp/1kWh. In case there are 2 possible numbers of impulses at your electro meter, the lower number is usually the right one for the SO output.\\
-The higher number tells you how often a LED diode at your electro meter switches on. </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:konfigurace:obrazek_elmeru.png?100  }}\\
-\\
-</WRAP> **Follow instruction bellow in order to setup a number of pulses different than 1000 per 1 kWh:**
-==== 1. Direct measuring ====
-In the electro meter's label or documentation find out how many pulses per 1 kWh your electro meter generates at the SO output. Fill in this value into relevant box in SM2-MU menu [[:en:sim:manual:menu_nastaveni:vstupy_a_vystupy|Inputs & Counters]].
-==== 2. Indirect measuring ====
-In the electro meter's label or documentation find out how many pulses per 1 kWh your electro meter generates at the SO output. Use this number in calculation, see example bellow.\\
-\\
-__Example: Electro meter's label states 10 000 impulses per 1 kWh.__ \\
-\\
-<WRAP half column> Look at the indirect power measuring transformer (1 transformer connected to each phase) and find a ratio (e.g. 150A/5A). Use the result of this ratio (30 in this example) in the formula (10 000/30). Fill in the whole formula (i.e. 10000/30) into relevant box in SM2-MU menu [[:en:sim:manual:menu_nastaveni:vstupy_a_vystupy|Inputs & Counters]]. </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:impulsy_neprime_mereni.png?direct&400  }} </WRAP>\\
-\\
-\\
-\\
-When you have changed the setup, remember to save the changes {{:en:sim:manual:rychly_navod:jak_na_to:tlacitko_ulozit.png?nolink&}}.\\
-\\
-<WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu|Next >>]] </WRAP> <WRAP left> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|<< Back]] </WRAP>