en:sim:manual:dohled_a_upozorneni:monitoring_a_alarmy
Differences
This shows you the differences between two versions of the page.
|
en:sim:manual:dohled_a_upozorneni:monitoring_a_alarmy [2018/06/18 13:36] ondra |
en:sim:manual:dohled_a_upozorneni:monitoring_a_alarmy [2018/06/18 13:41] (current) ondra |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| - | ==== PV plant monitoring ==== | + | ==== PV Plant Monitoring ==== |
| - | Table shows monitored components of a PV plant, their current status and limit values. It enables setting up the way of informing the user about alarms via e-mail or SMS. You can set up the limit values in the v menu "System set up%%\%%Sensors and alarms", see chapter 4.1.3 Sensors & Alerts.\\ | + | Table shows monitored components of a PV plant, their current status and limit values. It enables setting up the way of informing the user about alarms via e-mail or SMS. You can set up the limit values of sensors in the v menu "System set up%%\%%Sensors and alarms", see chapter 4.1.3 Sensors & Alerts.\\ |
| - | \\ | + | |
| - | **Loading pulses from the electrometer** \\ | + | |
| - | Production is monitored continuously. If no pulses come from the electrometer, countdown starts. When limit value is exceeded, notification is sent to the user.\\ | + | |
| - | \\ | + | |
| - | **Communication with the inverter** \\ | + | |
| - | Inverter's response on line RS-485 is monitored continuously. If there is no response, countdown starts. When limit value is exceeded, notification is sent to the user.\\ | + | |
| \\ | \\ | ||
| **Sensors** \\ | **Sensors** \\ | ||
| - | If any sensor connected to the unit exceeds the limit values, a notification to the user is sent. <WRAP info> Sensors in default setting have 60 seconds delay, inverters 5 seconds delay. Further info on setting up the delay in chapter 4.1.3 Sensors and alarms. </WRAP> **Inputs** \\ | + | If any sensor connected to the unit exceeds the limit values, a notification to the user is sent. <WRAP info> Sensors in default setting have 60 seconds delay, inverters 5 seconds delay. Further info on setting up the delay in chapter 4.1.3 Sensors and alarms. </WRAP> |
| + | **Inputs** \\ | ||
| When input status (connected / disconnected) changes in a way not allowed by the user, a notification to the user is sent immediately.\\ | When input status (connected / disconnected) changes in a way not allowed by the user, a notification to the user is sent immediately.\\ | ||
| \\ | \\ | ||
| Line 29: | Line 24: | ||
| \\ | \\ | ||
| **Sending production report** \\ | **Sending production report** \\ | ||
| - | A production report (selected type of message) is sent to the user in preset intervals.\\ | + | A production report (selected type of message) is sent to the user in preset intervals.\\ \\ |
| - | ==== Devices state ==== | + | ==== Devices State ==== |
| - | + | If a failure is detected at the device (e.g. inverter), a notification to the user is sent immediately. | |
| - | + | ||
| - | If a failure is detected at the inverter ("status" bar), a notification to the user is sent immediately. | + | |
en/sim/manual/dohled_a_upozorneni/monitoring_a_alarmy.1529321768.txt.gz · Last modified: 2018/06/18 13:36 by ondra
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
