en:sim:manual:jak_na_instalaci:steca
Differences
This shows you the differences between two versions of the page.
|
en:sim:manual:jak_na_instalaci:steca [2018/05/14 10:44] ondra |
en:sim:manual:jak_na_instalaci:steca [2018/05/25 15:21] (current) ondra |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Connection Diagram ===== | ===== Connection Diagram ===== | ||
| - | ==== 1a) SM2-MU – master in all cases ==== | + | ==== 1a) SM2-MU – master for all devices ==== |
| - | For power supply in Power Supply. | + | For power supply see Power Supply section. |
| All individual Taroms connected as slaves - data are read from each device. | All individual Taroms connected as slaves - data are read from each device. | ||
| {{ .:sm2_mu_steca_slave_scheme.png?direct |}} | {{ .:sm2_mu_steca_slave_scheme.png?direct |}} | ||
| Line 9: | Line 9: | ||
| \\ \\ | \\ \\ | ||
| 1a) and 1b) can be mixed \\ | 1a) and 1b) can be mixed \\ | ||
| - | Both 1a) and 1b) can be used for each SM2-MU interface. | + | Both 1a) and 1b) can be used for each SM2-MU interface. \\ |
| + | For short cables terminator is not necessary. | ||
| \\ \\ | \\ \\ | ||
| - | ==== 1d) Other bus cabling example using the MPPT 6000-M, MPPT 6000-S ==== | + | ==== 1c) SM2-MU can be placed in the middle of RS485 bus ==== |
| - | Second SM2-MU serial interface can be used for additional Tarom device. | + | For this case SM2-MU must be used with RS485 terminator switched off. Use yellow DIP switches to achieve this. |
| + | {{ .:sm2_mu_steca_master_scheme_switched_off.png?direct |}} | ||
| + | \\ \\ | ||
| + | ==== 1d) Second SM2-MU serial interface can be used for additional Tarom device. ==== | ||
| + | {{ .:sm2_mu_steca_master_scheme_2_branches.png?direct |}} | ||
| + | |||
| + | \\ \\ | ||
| + | ==== 1e) Other bus cabling example using the MPPT 6000-M, MPPT 6000-S ==== | ||
| + | MPPT 6000-S as slaves to MPPT 6000-M | ||
| {{ .:sm2_mu_steca_master_and_slave_connection.png?direct |}} | {{ .:sm2_mu_steca_master_and_slave_connection.png?direct |}} | ||
| \\ \\ | \\ \\ | ||
| - | ==== 1e) SM2-MU + Tarom 4545 ==== | + | ==== 1f) SM2-MU + Tarom 4545 ==== |
| {{ .:sm2_tarom4545.png?direct |}} | {{ .:sm2_tarom4545.png?direct |}} | ||
| \\ \\ | \\ \\ | ||
| **Detection** | **Detection** | ||
| - | {{ .:detection.png?direct |}} | + | {{ .:detection.png?direct |}} \\ \\ |
| + | <WRAP left> | ||
| + | [[..:jak_na_instalaci:stridace|<< Back]] | ||
| + | </WRAP> | ||
en/sim/manual/jak_na_instalaci/steca.1526287492.txt.gz · Last modified: 2018/05/14 10:44 by ondra
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
