Uživatelské nástroje

Nástroje pro tento web


en:sim:manual:jak_na_instalaci:stridace
no way to compare when less than two revisions

Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.


Předchozí verze
Následující verze
en:sim:manual:jak_na_instalaci:stridace [2018/03/21 13:44] ondra
Řádek 1: Řádek 1:
 +===== Inverters =====
 +
 +
 +----
 +
 +
 +\\ 
 +<WRAP half column>\\ 
 +\\ 
 +\\ 
 +Terminals SM2-MU: A, B, 4GND, Z, Y, or DC+ a DC - are used according to the inverter manufacturer. </WRAP> <WRAP half column> {{  ..:rychly_navod:jak_na_to:stridace_svorky.png?nolink&250  }}\\ 
 +\\ 
 +</WRAP>\\ 
 +\\ 
 +If there is SM at the beginning of H-bus, sliding switches must be in ON position.\\ 
 +\\ 
 +{{  .:zakonceni_sbernice.png?nolink&400  }}
 +
 +
 +The same for the inverter - if it supports bus termination, the last one should be switched on according to the manufacturer's instructions. Description of inverter connection to the Solar Monitor unit and whether it supports the bus is to be found in the following table.\\ 
 +If there is manual address scheme in your inverters, you need to set up addresses, ideally beginning with address 1. E.g. 21: 1, 2, 3, …, 31. Procedure is described in inverter's manual. Usually set up with DIP switches or in LCD  inverter menu.
 +
 +
 +^  SM2-MU  ^  Z  ^  Y  ^  4GND  ^  B  ^  A  ^  DC+  ^  DC-  ^  Bus termination  ^  Hand addressing  ^  Transmission speed  |
 +|[[.:aeg_layout|AEG]]  |  4(Rx-)  |  3(Rx+)  |  1(GND)  |  5(Tx-)  |  6(Tx+)  |  -  |  -  |  ✔  |  -  |  9600  |
 +|[[.:aurora|Power - One (Aurora)]]  |  -  |  -  |  RTN  |  -T/R  |  +T/R  |  -  |  -  |  ✔  |  ✔  |  optional  |
 +|Carlo Gavazzi |  -  |  -  |  5(GND)  |  8(RXB)  |  7(TXA)  |  -  |  -  |  ✔  |  -  |  optional  |
 +|[[.:danfoss|Danfoss]] |  -  |  -  |  1  |  3  |  6  |  -  |  -  |  ✔  |  -  |  19200  |
 +|[[.:delta|Delta]] |  -  |  -  |  GND  |  6  |  7  |  -  |  -  |  ✔  |  ✔  |  optional  |
 +|[[.:diehl|Diehl]] |  -  |  -  |  shield  |  B  |  A  |  -  |  -  |  ✔  |  -  |  19200  |
 +|[[.:fronius_layout|Fronius]]\\ IN\\ OUT |  \\ 5\\ 6  |  \\ 4\\ 3  |  \\ 2\\ 2  |  \\ 6\\ 5  |  \\ 3\\ 4  |  \\ -\\ -  |  \\ -\\ -  |  \\ ✔\\ ✔  |  \\ ✔\\ ✔  |  \\ optional\\ optional  |
 +|[[.:kaco|Kaco]] |  -  |  -  |  -  |  A  |  B  |  -  |  -  |  ✔  |  ✔  |  9600  |
 +|KOSTAL |  -  |  -  |  3  |  2  |  1  |  -  |  -  |  ✔  |  ✔  |  19200  |
 +|Mastervolt |- |  -  |  -  |  3  |  4  |  -  |  -  |  ✔  |  -  |  9600  |
 +|[[.:omron|Omron]] |  -  |  -  |  6: GO  |  8: A-  |  7: B+  |  -  |  -  |  ✔  |  ✔  |  optional  |
 +|Refusol |  -  |  -  |  -  |  3  |  2  |  -  |  -  |  ✔  |  ✔  |  57600  |
 +|Santerno |- |  -  |  -  |  S-  |S+ |  -  |  -  |  ✔  |  -  |  optional  |
 +|[[.:schneider|Schneider (SunEzy)]]  |  4(Rx-)  |  3(Rx+)  |  1(GND)  |  5(Tx-)  |  6(Tx+)  |  -  |  -  |  ✔  |  -  |  9600  |
 +|Siemens |  -  |  -  |  -  |  B  |  A  |  -  |  -  |  ✔  |  ✔  |  optional  |
 +|Siliken |  -  |  -  |  5(GND)  |  8(RXB)  |  7(TXA)  |  -  |  -  |  ✔  |  -  |  optional  |
 +|[[.:sma|SMA]] |  -  |  -  |  5  |  7  |  2  |  -  |  -  |  ✔  |  -  |  1200  |
 +|[[.:solarmax|Solar Max]]  |  -  |  -  |  8  |  7  |  2(15V)  |  3  |  -  |  ✔  |  ✔  |  19200  |
 +|[[.:studer|Studer]] |  2  |  3  |  5  |  -  |  -  |  -  |  -  |  ✔  |  -  |  115200  |
 +|[[.:sungrow|Sungrow]]  |  -  |  -  |  3  |  6  |  -  |  -  |  ✔  |  ✔  |  optional  |
 +|[[.:sunville|Sunville]]  |  4(Rx-)  |  3(Rx+)  |  1(GND)  |  5(Tx-)  |  6(Tx+)  |  -  |  -  |  ✔  |  -  |  9600  |
 +|Vacon |  -  |  -  |  5  |  3  |  4  |  -  |  -  |  ✔  |  ✔  |  optional  |
 +|Xantrex (GT100-630E) |  -  |  -  |  GND  |  RxTx-  |  RxTx+  |  -  |  -  |  ✘  |  optional  |  optional  |
 +
 +
 +\\
 +
  
en/sim/manual/jak_na_instalaci/stridace.txt · Poslední úprava: 2019/09/30 11:52 autor: ppodhajska