en:sim:manual:menu_nastaveni:stridace_a_mereni:ethernet
no way to compare when less than two revisions
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Předchozí verzeNásledující verze | |||
— | en:sim:manual:menu_nastaveni:stridace_a_mereni:ethernet [2017/12/01 12:36] – ondra | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
+ | ===== Reading Inverters via Ethernet ===== | ||
+ | |||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | <WRAP half column> | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | To be set up in the submenu Inverters & Meters </ | ||
+ | </ | ||
+ | <WRAP half column> | ||
+ | \\ | ||
+ | Select the manufacturer of your inverter. </ | ||
+ | \\ | ||
+ | <WRAP info> Setting up network interface has two address modes: | ||
+ | 1. IP Address - communication in local network \\ | ||
+ | 2. Port - remote communication via public IP address of router with translation of addresses (NAT) \\ | ||
+ | </ | ||
+ | ==== IP Address Detection of Inverters ==== | ||
+ | |||
+ | |||
+ | Use this type of detection if inverters and Solar Monitor are in the same local network.\\ | ||
+ | \\ | ||
+ | <WRAP info> Address the inverters first. Assign consequent IP addresses to the inverters and the port number. The port number is the same for all inverters. Further info on how to address the inverters to be found in inverter' | ||
+ | \\ | ||
+ | **IP Address** \\ | ||
+ | Enter inverter with the lowest IP address in the network. Detection starts with this address and searches for following higher IP addresses until the required number of destinations has been searched.\\ | ||
+ | \\ | ||
+ | {{ .: | ||
+ | Enter port's number.\\ | ||
+ | \\ | ||
+ | <WRAP half column> </ | ||
+ | Select addressing mode depending on the IP address.\\ | ||
+ | \\ | ||
+ | **The number of destinations** \\ | ||
+ | The number of IP addresses of all devices.\\ | ||
+ | \\ | ||
+ | **Detected devices** \\ | ||
+ | The number of devices assigned to each destination.\\ | ||
+ | \\ | ||
+ | **Read Connected Inverters** \\ | ||
+ | Click on button{{..: | ||
+ | \\ | ||
+ | Detection can take up to several minutes depending on the type of protocol and the number of inverters. <WRAP info> To be detected, inverters must be on, i.e. they must have sufficient electric current coming from the PV panels. </ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | Save changes you have made{{..: | ||
+ | \\ | ||
+ | </ | ||
+ | \\ | ||
+ | ==== Port Detection of Inverters ==== | ||
+ | |||
+ | |||
+ | Select this method of detection if **there is a router with network address translation (NAT) between the inverters and the Solar Monitor**. The Solar Monitor will access to the inverters via one router´s address. Assign different, consecutive ports for the local IP addresses of the inverters in the router. If the router is connected to the Internet, router´s IP address must be public. \\ | ||
+ | \\ | ||
+ | <WRAP info> Address the inverters first. Assign different IP addresses to the inverters in your local network. In the router through which the Solar Monitor will access to the inverters, assign consecutive port numbers to the local IP addresses of the inverters. Further info on how to address the inverters to be found in inverter' | ||
+ | \\ | ||
+ | **IP address** \\ | ||
+ | Enter the public IP address which you use for the access to the local network.\\ | ||
+ | \\ | ||
+ | {{ .: | ||
+ | Enter inverter with the lowest port number (destination) at a particular IP address. Detection starts with this port and searches for following higher port numbers until the required number of destinations has been searched.\\ | ||
+ | \\ | ||
+ | <WRAP half column> </ | ||
+ | Select addressing mode according to the port.\\ | ||
+ | \\ | ||
+ | **The Number of Destinations** \\ | ||
+ | The number of ports where the devices have been addressed.\\ | ||
+ | \\ | ||
+ | **Detected devices** \\ | ||
+ | The number of devices assigned to each destination.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | **Read connected inverters**\\ | ||
+ | Click on button{{..: | ||
+ | \\ | ||
+ | Detection can take up to several minutes depending on the type of protocol and the number of inverters. <WRAP info> To be detected, inverters must be on, i.e. they must have sufficient electric current coming from the PV panels. </ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | Save the changes you have made {{..: | ||
+ | \\ | ||
+ | </ | ||
en/sim/manual/menu_nastaveni/stridace_a_mereni/ethernet.txt · Poslední úprava: 2018/06/11 09:30 autor: ondra