no way to compare when less than two revisions

Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.

@@ Řádek 1: / Řádek 1: @@
+===== Basic module parameters =====
+----
+{{  .:sm2_vykres.png?nolink&  }}
+^Max. number of devices ^  |
+|SM2-MU Basic and SM2-MU Start|  1 device |
+|SM2-MU 60 |  6 devices |
+|SM2-MU 300 |  30 devices |
+|SM2-MU 1000 |  100 devices |
+^  ^  |
+|  |  |
+^Supported devices ^  Ethernet or serial bus connected |
+|Communication |  Ethernet (TCP), up to 3 serial ports |
+|Inverter protocols |  AEG, Carlo Gavazzi, Danfoss, Delta, Diehl, Fronius, IBC Solar, Kaco, Kostal, Mastervolt, Morningstar, Omron, Pairan, Power‑One, Refusol, Riello UPS, Santerno, Satcon, Schneider‑Electric, Siemens, Siliken, SMA, Solarmax, Solutronic, Studer, Sungrow, Sunville, Sunways, Vacon, Xantrex |
+|Meter protocols |  ABB (REX521), Carlo Gavazzi (VMU-E/X), Fronius (Smart Meter), KMB (SMC-144, PA-144), Phoenix Contact (MA200/250), Schneider‑Electric (SEPAM, PM9), Yorix (GreenBonO), ZPA (IEC 62056-21) |
+^  ^  |
+|  |  |
+^Sensors ^  Dallas 1-wire bus |
+|Interface |  Screw terminals for 05 mm² - 15 mm² cores |
+|Max. count  |  10 sensors |
+|Max. distance  |  100 m, recommended max. cable length for daisy‑chained sensors with minimal trunk segments |
+^  ^  |
+|  |  |
+^Ethernet interface (LAN) ^  |
+|Interface |  RJ45 (100BASE-T) -100Mbit/s, compatible with networks 10/100/1000 Mbit/s, auto MDIX |
+|Protocols |  HTTP, SOAP, DNS, UDP Setup, Telnet, ARP, ICMP, SMTP, SNMP, Modbus |
+^  ^  |
+|  |  |
+^RS485 / RS422 / RS232 ^  |
+|Interfaces  |  2x RS485 or 1x RS422 |
+|  |  |
+|  |  __//piggy-back hardware options//__ |
+|  |  2x RS485 or 1x RS422 opto-isolated |
+|  |  1x RS485 + 1x RS232 |
+|  |  1x RS485 + 1x RS232 opto-isolated |
+|  |  |
+|  |  //__SM2-BE extension module__// |
+|  |  1x RS232 + 1x RS485 surge protected |
+|  |  |
+|Speed  |  300 .. 115.200 bps (software configurable) |
+|Termination  |  Yes, both for half and full duplex, configurable with jumpers |
+^  ^  |
+|  |  |
+^Inputs |  opto-electronically isolated |
+|3x digital inputs (DI) |  software configurable between dry contact or S0 pulse meter inputs (e.g. from electrometer) |
+|Max. distance |  30 m (depends on cable) |
+^  ^  |
+|  |  |
+^Inputs (opto-electronic separated) |  |
+|Interface |  bus 0,5 mm² - 1,5 mm², 2 inputs, 1 electrometer SO connection |
+|Max. distance |  30m |
+^  ^  |
+|  |  |
+^Outputs |  |
+|1x relay  |  32 V, 3 A, protected with power fuse |
+^  ^  |
+|  |  |
+^Electrical parameters |  |
+|Dimensions |  71,6 x 89,7 x 62,2 mm |
+|Operating temperature |  0 up to + 70 °C |
+|LED diodes |  Status, RS485, Sensors |
+^  ^  |
+|  |  |
+^Power parameters |  |
+|Power supply |  9-35 V DC, typ. 1.2 W @ 12V |
+|DI1, DI2, DI3 |  8-80 V |
+|1 Wire |  Interface provides 5 V power supply, max. 350 mA, protected with 500 mA power fuse. |
+|RS485 |  Protected against transient voltages above 6.8V and against high currents with 10Ω resistors. Additional surge protection can be achieved with SM2-BE (bus extension) module with gas discharge tubes: |
+|  |  Minimum DC Sparkover	(100 V/s) 185 V |
+|  |  Service life: |
+|  |  150 operations	8/20 μs 250 A, 1.2/50, 500 V (IEC61643-21) |
+|  |  20 operations	2/10 μs, 5 kV, 500 A |
+|  |  2 operations	8/20 μs, 1 kA |
+^  ^  |
+|  |  |
+^Mechanical parameters |  |
+|Dimensions  |  71.6 x 89.7 x 62.2 mm |
+|Mounting  |  DIN rail |
+|Screw terminals  |  05 mm² - 15 mm² cable cores |
+|Operating temperature  |  0 .. +70 °C |
+|LED diodes  |  Status, RS485, Sensors |
+^  ^  |
+|  |  |
+^Extension options |  |
+|Interface  |  HBUS (DIN rail, bottom pluggable, no external wires needed) |
+|Extension modules  |  SM2-PC, SM2-AD, SM2-DI, SM2-GSM, SM2-BE |
+\\