en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu
Differences
This shows you the differences between two versions of the page.
|
en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu [2018/06/27 14:13] ondra |
en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu [2018/09/14 12:26] (current) jitka |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== Inverter Configuration ===== | + | ===== Step 2 - Interface Settings ===== |
| Line 5: | Line 5: | ||
| - | <WRAP half column>\\ | + | Select interface for communication with the inverter and then protocole type and transmission speed.\\ |
| + | After that click on Next button on the right to get to the next step.\\ | ||
| + | <WRAP info> For more detailed info on setting go to chapter [[:en:sim:manual:menu_nastaveni:stridace_a_mereni|Find Devices]]. </WRAP> {{ :en:sim:manual:rychly_navod:konfigurace:krok2.png?direct& }}\\ | ||
| \\ | \\ | ||
| - | \\ | + | <WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:detekce_senzoru|Next >>]] </WRAP> <WRAP left> [[:en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu|<< Back]] </WRAP> |
| - | \\ | + | |
| - | Go to menu Settings/Find Devices </WRAP> <WRAP half column> {{ ..:jak_na_to:detekce_zarizeni.png?direct&100 }}\\ | + | |
| - | </WRAP> You need to set up communication parameters for **RS 485 interface**.\\ | + | |
| - | \\ | + | |
| - | <WRAP info> In case of communication with inverters via **RS 232 interface ** or via **Ethernet**, info on setup is in [[..:..:menu_nastaveni:stridace_a_mereni|Find Devices]]. </WRAP>\\ | + | |
| - | \\ | + | |
| - | <WRAP half column> </WRAP> <WRAP half column>\\ | + | |
| - | Select manufacturer of your inverter </WRAP> <WRAP half column> {{ ..:jak_na_to:typ_protokolu.png?nolink& }} </WRAP>\\ | + | |
| - | \\ | + | |
| - | <WRAP half column>\\ | + | |
| - | \\ | + | |
| - | Select data transfer rate. The same data transfer rate must be set up in all inverters and in the Solar Monitor. </WRAP> <WRAP half column> {{ ..:jak_na_to:prenosova_rychlost.png }} </WRAP> | + | |
| - | \\ \\ | + | |
| - | To save the changes in setup click on the button {{..:jak_na_to:tlacitko_ulozit.png?nolink&}}. | + | |
| - | \\ \\ \\ | + | |
| - | Pro vyhledání připojených střídačů k SM2-MU na všech rozhraních (RS 485, RS 232, ethernet) stiskněte tlačítko {{..:jak_na_to:automatická detekce.png?nolink|}} \\ \\ | + | |
| - | Pokud chcete detekovat jen na vybraném rozhraní stiskněte tlačítko {{..:jak_na_to:manualni_detekce.png?nolink|}} \\ \\ | + | |
| - | Manuální detekci využijete ve chvíli, kdy už nějaká zařízení nadetekovaná máte (např. na rozhraní RS 485-AB) a chcete nadetekovat zařízení na jiném rozhraní, aniž byste předetekovali již nadetekované. \\ \\ | + | |
| - | \\ | + | |
| - | When the identification has finished, the list of connected inverters is displayed.\\ | + | |
| - | + | ||
| - | + | ||
| - | For detailed info on inverter's output, click on the particular inverter in the menu [[..:..:prehledy:prehled_vyroby|Overview]].\\ | + | |
| - | \\ | + | |
| - | <WRAP right> [[.:detekce_senzoru|Next >>]] </WRAP> <WRAP left> [[.:nastaveni_pulzu|<< Back]] </WRAP> | + | |
en/sim/manual/rychly_navod/konfigurace/konfigurace_stridacu.1530101590.txt.gz · Last modified: 2018/06/27 14:13 by ondra
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
