en:sim:rm:rychly_navod:jak_na_to

9. Inputs Configuration

Anonymous (anonymous@undisclosed.example.com) — 2014-09-10T14:46:15+00:00

9. Inputs Configuration ---------- In previous chapter we have dealt with setting up pulses in the electro meter. In case there is only electro meter connected to your SM2-RM device, go to Next >> Inputs configuration is carried out in the menu System Setup/Inputs and Measurement (same menu as Pulse Setup)

1. Installation

Anonymous (anonymous@undisclosed.example.com) — 2014-08-28T13:43:34+00:00

1. Installation ---------- SM2-RM unit has been designed for indoor use. When used outdoor, it requires sufficient protection from external impacts and the range of operational temperatures must be respected. The values concerned to be found in chapter

8. How to Setup Reading Pulses from the Electrometer

Anonymous (anonymous@undisclosed.example.com) — 2014-09-12T12:57:49+00:00

8. How to Setup Reading Pulses from the Electrometer ---------- In SM2-RM web interface go to menu System Setup/Inputs and Measurement Fill in meter's name and set up the right number of pulses per 1 kWh. Default setting is reading 1000 pulses per 1 kWh. If your electro meter shows a different number, change the setting. If it is 1000 pulses, go to

7. Unit's Name

Anonymous (anonymous@undisclosed.example.com) — 2014-09-10T13:59:24+00:00

7. Unit's Name ---------- In SM2-RM web interface go to menu System Setup Fill in the box Unit's Name in System Setup Orange question mark conceals help for relevant box or button. In order to show the help, place mouse cursor at the question mark.

10. Sending data to the Portal

Anonymous (anonymous@undisclosed.example.com) — 2014-09-10T14:59:47+00:00

10. Sending data to the Portal ---------- Solar Monitor Portal offers detailed analysis and reporting to . With your permission the data from devices connected to SM2-RM inputs is recorded at the Portal. How to Enable Sending Data Go to menu System Setup/Time and Network in your SM2-RM.

4. Connecting Digital Inputs

Anonymous (anonymous@undisclosed.example.com) — 2014-08-28T13:49:00+00:00

4. Connecting Digital Inputs ---------- SM2-RM has three digital inputs DI available. Connect DC- supply signal to DCOM terminal. In order to switch the input on, voltage between terminals DCOM and DI (DI1-DI3) must be higher than 8V. Next >>

2. Connecting to the Electro Meter

Anonymous (anonymous@undisclosed.example.com) — 2015-02-10T09:47:18+00:00

2. Connecting to the Electro Meter ---------- Connect SM2-RM to the meter with its S0 (pulse) output as shown in the following picture: Connecting in case both SM2-RM and meter each has its power supply: Next >> << Previous

5. Connecting Power Supply

Anonymous (anonymous@undisclosed.example.com) — 2014-08-28T13:50:24+00:00

5. Connecting Power Supply ---------- Connect the power supply (9-42V) to SM2-RM unit as shown in the following picture. Next >> << Previous

3. LAN Network

Anonymous (anonymous@undisclosed.example.com) — 2014-08-28T13:47:16+00:00

3. LAN Network ---------- Connect the unit into LAN network (to the switch, PC) with straight or cross-over UTP cable. Connect the UTP cable into RJ45 terminal of SM2-RM. The device is connected if a green light “LINK” at the RJ45 terminal is on.

6. Detecting Unit in the Network, Interface Display

Anonymous (anonymous@undisclosed.example.com) — 2020-01-15T10:12:02+00:00

6. Detecting Unit in the Network, Interface Display ---------- SM2-RM unit has DHCP client regime allowed in its default setting- IP address is allocated automatically from DHCP server in local network (if available). If there is no DHCP server in your network, the device attempts to get the IP address for 20 seconds, after that it is possible to connect to the IP address