en:sim:manual:menu_nastaveni:vstupy_a_vystupy
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verzeNásledující verzeObě strany příští revize | ||
en:sim:manual:menu_nastaveni:vstupy_a_vystupy [2014/09/11 13:54] – ondra | en:sim:manual:menu_nastaveni:vstupy_a_vystupy [2018/09/20 11:01] – jitka | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
- | ===== Inputs | + | ===== Inputs |
Řádek 5: | Řádek 5: | ||
- | Submenu Inputs and Outputs | + | Submenu Inputs and Counters |
\\ | \\ | ||
- | {{ | + | Default setting of the chart\\ |
+ | {{ :en: | ||
- | ==== Setting up the Inputs ==== | + | ==== Inputs |
- | **Permit Input 3** \\ | + | **Select input function** \\ |
- | Use DI 3 input if you wish to display power from the electrometer. If you want to connect another device to this input, tick the box. | + | Solar Monitor has 3 inputs available. Each works as: |
- | The table contains current inputs status. Set up the values. | + | === a) Input = binary input === |
- | ==== Setting up the Outputs ==== | + | This chart presents |
+ | {{ : | ||
+ | Choose if you want to receive report (by email or SMS) when input changes status (on/off).\\ | ||
+ | === b) Counter | ||
- | **Permit Output Module** | + | In the chart Inputs and Counters select function Counter for the particular input where meter is connected.\\ |
- | Tick, if there is an output | + | <WRAP info> Meter can be connected to any of the 3 inputs. There can be up to 3 meters at each SM2-MU. </ |
+ | After you have chosen function Counter, its setup chart appears.\\ | ||
+ | {{ : | ||
+ | Enter its name (e.g. electrometer) and select its type.\\ | ||
+ | Enter the correct number of pulses per 1 kWh (as specified in SO output at the counter).\\ | ||
+ | <WRAP info> In default setting | ||
+ | Number of pulses per 1 kWh is normally between 250-1000 imp/1kWh. If your electrometer has two numbers of pulses, the right SO output | ||
+ | Higher number says how many times light diode at the electrometer flashes. </ | ||
\\ | \\ | ||
- | **Delay for Switching on the Outputs** \\ | + | </ |
- | Set up the delay from reaching switch on conditions until it is really switched on. The delay prevents switching on for short time only, when switch on condition fluctuates about the limit value. | + | === For direct measurement === |
- | ==== Switching on the Outputs ==== | + | Find out how many pulses per kWh does your electrometer generate at SO output. This information is available at the label or in its documentation. Enter this number into the box Pulses Count in SM2-MU.\\ |
+ | === For indirect measurement | ||
- | You can name the inputs and set up what will switch them on and on what conditions. The table contains current status too. | + | <font 12.8px/ |
+ | \\ | ||
+ | __Example: Electrometer specification says there is 10 000 pulses per 1 kWh.__ \\ | ||
+ | \\ | ||
+ | <WRAP half column> Check transformer of indirect power measurement which is connected to electrometer (each phase one transformer). | ||
+ | \\ | ||
+ | </ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | </ | ||
+ | |||
+ | |||
+ | === c) Vstup a Čítač = čítání ze zařízení detekovaných na RS485, RS232, Ethernetu + lze použít i jako binární vstup === | ||
+ | |||
+ | |||
+ | {{ : | ||
+ | Po zvolení funkce Vstup a Čítač se nad tabulkou vstupů zobrazí tabulka nastavení čítače.\\ | ||
+ | Pokud je nastaveno, že jde např. o výrobu střídače, | ||
+ | {{ : | ||
+ | Pokud využíváte tento vstup také jako binární, nastavte jeho povolenou hodnotu\\ | ||
+ | \\ | ||
+ | Po každé změně v nastavení stikněte tlačítko {{: | ||
en/sim/manual/menu_nastaveni/vstupy_a_vystupy.txt · Poslední úprava: 2019/03/01 12:01 autor: ondra