en:sim:manual:rozsirujici_moduly:sm2_ad:nast_analog_vystupu
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Následující verze | Předchozí verzePoslední revizeObě strany příští revize | ||
en:sim:manual:rozsirujici_moduly:sm2_ad:nast_analog_vystupu [2014/07/09 08:58] – external edit 127.0.0.1 | en:sim:manual:rozsirujici_moduly:sm2_ad:nast_analog_vystupu [2018/06/25 09:18] – ondra | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
- | ===== Nastavení analogového výstupu | + | ===== Analog Outputs Setup ===== |
+ | |||
---- | ---- | ||
- | Pokud u modulu SM2-AD nechcete řídit napětí na jeho analogovém výstupu, pokračujte na [[.: | ||
- | \\ \\ | ||
- | Nastavení | ||
- | __Příklad 1: Regulace otáček ventilace__ \\ | ||
- | Nastavíme, v jakém rozsahu teplot, bude na výstupu | ||
- | Tzn.: \\ | ||
- | y = kolik voltů z rozsahu 0 (V) až 10 (V) bude dávat výstup při zadaném teplotním rozsahu \\ | ||
- | zadaný rozsah teplot: x1 = spodní mez (°C) až x2 = horní mez (°C), např. 15 - 40 °C \\ | ||
- | x = aktuální teplota v místnosti (°C), např. 28 °C \\ \\ | ||
- | y = [10 / (x2 - x1)] * (x - x1) \\ | ||
- | y = [10 / (40 - 15)] * (28 - 15) \\ | ||
- | y = 5,2 V \\ | ||
- | \\ \\ | ||
- | __Příklad 2: Nabíjení akumulátoru__ \\ | ||
- | V tomto příkladu nastavíme, v jakém rozsahu výkonu elektrárny, | ||
- | Tzn.: \\ | ||
- | y = kolik voltů z rozsahu 0 (V) až 10 (V) bude dávat výstup při zadaném rozsahu výkonu elektrárny \\ | ||
- | zadaný rozsah výkonu elektrárny: | ||
- | x = aktuální výkon elektrárny (W), např. 5200 W \\ \\ | ||
- | y = [10 / (x2 - x1)] * (x - x1) \\ | ||
- | y = [10 / (10000 - 2500)] * (5200 - 2500) \\ | ||
- | y = 3,6 V | ||
- | \\ \\ | ||
- | {{ ..: | + | |
- | <WRAP right> | + | In case you don't intend to control voltage at your SM2-AD module' |
- | [[.: | + | \\ |
- | </ | + | Open menu " |
- | <WRAP left> | + | \\ |
- | [[.: | + | We set up analog output in the same way as digital outputs. Select the factor determining the output setup (e.g. temperature in the room with inverters, PV plant' |
- | </ | + | \\ |
+ | __1st example: Regulation of Ventilation Revolving__ \\ | ||
+ | Set up the temperature range corresponding to value 0 - 10 V at the output. The temperature is going to determine ventilation revolving.\\ | ||
+ | \\ | ||
+ | I.e.:\\ | ||
+ | y = the number of Volts in the range from 0 (V) to 10 (V) that output will deliver with a given temperature range\\ | ||
+ | given temperature range: x1 = minimum (°C) to x2 = maximum (°C), e.g. 15 - 40 °C\\ | ||
+ | x = current temperature in the room (°C), e.g. 28 °C\\ | ||
+ | \\ | ||
+ | y = [10 / (x2 - x1)] * (x - x1)\\ | ||
+ | y = [10 / (40 - 15)] * (28 - 15)\\ | ||
+ | y = 5,2 V\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | __2nd example: Charging Storage Battery__ \\ | ||
+ | Set up PV plant' | ||
+ | \\ | ||
+ | I.e.:\\ | ||
+ | y = the number of Volts in the range from 0 (V) to 10 (V) that output will deliver with a given PV plant' | ||
+ | given PV plant' | ||
+ | x = current PV plant' | ||
+ | \\ | ||
+ | y = [10 / (x2 - x1)] * (x - x1)\\ | ||
+ | y = [10 / (10000 - 2500)] * (5200 - 2500)\\ | ||
+ | y = 3,6 V\\ | ||
+ | {{ ..: | ||
+ | \\ | ||
+ | <WRAP right> [[.: |
en/sim/manual/rozsirujici_moduly/sm2_ad/nast_analog_vystupu.txt · Poslední úprava: 2018/06/25 12:16 autor: ondra