en:sim:manual:rozsirujici_moduly:sm2_pc
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verzeNásledující verzeObě strany příští revize | ||
en:sim:manual:rozsirujici_moduly:sm2_pc [2016/10/04 14:15] – ondra | en:sim:manual:rozsirujici_moduly:sm2_pc [2017/08/10 10:01] – ondra | ||
---|---|---|---|
Řádek 5: | Řádek 5: | ||
- | PC module (Power Control) controls your PV plant' | + | PC module (Power Control) controls your PV plant' |
\\ | \\ | ||
- | {{ .: | + | **Power control signals wiring** |
\\ | \\ | ||
+ | Signal DC- has to be connected to ACOM and BCOM terminals in order to control the power. Signal DC+ has to be connected to the multiple terminal of power control source (net operator' | ||
\\ | \\ | ||
+ | {{ .: | ||
\\ | \\ | ||
- | **Specification** \\ | + | **Start and configuration** \\ |
+ | \\ | ||
+ | As soon as the modules are connected and Solar Monitor unit is connected to the power supply, a green LED diode indicating status should glow. In case it doesn' | ||
+ | \\ | ||
+ | {{ .: | ||
+ | If you wish to use PC module for more Solar Monitor units, select option " | ||
+ | \\ | ||
+ | {{ .: | ||
+ | |||
+ | |||
+ | \\ | ||
+ | |||
+ | ==== Specification ==== | ||
+ | <WRAP half column> | ||
^Binary inputs | 2 x 5 inputs with usual Vcc a GND | | ^Binary inputs | 2 x 5 inputs with usual Vcc a GND | | ||
^ ^ | | ^ ^ | | ||
Řádek 28: | Řádek 43: | ||
| | | | | | | | ||
^Power supply | 12 – 24 V DC, max 100 mA | | ^Power supply | 12 – 24 V DC, max 100 mA | | ||
+ | ^ ^ | | ||
+ | | | | | ||
+ | ^Degree of protection | IP20 | | ||
^ ^ | | ^ ^ | | ||
| | | | | | | | ||
^Temperature range | -25 °C to +60 °C | | ^Temperature range | -25 °C to +60 °C | | ||
- | + | </ | |
- | + | <WRAP half column> | |
- | \\ | + | {{ .:moduly_vykres.png? |
- | \\ | + | </WRAP> |
- | **Power control signals wiring** \\ | + | |
- | \\ | + | |
- | Signal DC- has to be connected to ACOM and BCOM terminals in order to control the power. Signal DC+ has to be connected to the multiple terminal of power control source (net operator' | + | |
- | \\ | + | |
- | {{ .:pc-pripojeni_signalu.png? | + | |
- | \\ | + | |
- | **Start and configuration** \\ | + | |
- | \\ | + | |
- | As soon as the modules are connected and Solar Monitor unit is connected to the power supply, a green LED diode indicating status should glow. In case it doesn' | + | |
- | \\ | + | |
- | {{ .: | + | |
- | If you wish to use PC module for more Solar Monitor units, select option " | + | |
- | \\ | + | |
- | {{ .: | + | |
- | + | ||
- | + | ||
- | \\ | + |
en/sim/manual/rozsirujici_moduly/sm2_pc.txt · Poslední úprava: 2018/06/25 15:43 autor: ondra