Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.

--- en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu [2014/08/19 09:04] – ondra
+++ en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu [2018/08/27 14:39] – ondra
@@ Řádek 1: / Řádek 1: @@
-===== How to Setup Reading Pulses from the Electro Meter =====
+===== Step 4 - Counter Settings =====
 ----
+Pokud nemáte k Solar Monitoru připojený žádný čítač (elektroměr, plynoměr, vodoměr, střídač, tracker, baterii nebo jiné měřidlo), přejděte na [[.:emaily_sms|Další >>]] \\ \\
+{{ .:krok4.png?direct |}} \\
-In case there is no electro meter connected to your Solar Monitor, go to [[:en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu|Next >>]]\\
+Aby bylo možné vybraný vstup nastavit, nejprve je nutné ho povolit. \\
-\\
+{{ .:krok4a.png?direct |}} \\
-<WRAP half column>\\
+Dále zvolte o jaký čítač se jedná. \\
-\\
+{{ .:krok4b.png?direct |}}
-\\
+\\ \\
-\\
+Kliknutím vpravo na šipku Další přejděte na další krok.
-In SM2-MU web interface go to menu System setup/Inverters & Meters </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:stridace_a_mereni.png?100  }}\\
+<WRAP right>
-</WRAP> <WRAP half column>\\
+[[.:emaily_sms|Next >>]]
-In Energy measuring setup select reading energy from the electro meter and set up the right number of pulses per 1 kWh.\\
+</WRAP>
-</WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:pulzy.png?200  }}\\
+<WRAP left>
-</WRAP>\\
+[[.:detekce_senzoru|<< Back]]
-\\
+</WRAP>
-<WRAP half column>\\
-\\
-Enter PV plant's installed output and production eletro meter's status. </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:vykon_a_korekce.png?200  }}\\
-</WRAP>\\
-<WRAP info> Default setting is reading 1000 pulses per 1 kWh. If your electro meter shows a different number, change the setting. If it is 1000 pulses, go to [[:en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu|Next >>]]. </WRAP> <WRAP half column> </WRAP> <WRAP half column>\\
-The number of impulses per 1 kWh is usually between 250-1000 imp/1kWh. In case there are 2 possible numbers of impulses at your electro meter, the lower number is usually the right one for the SO output.\\
-The higher number tells you how often a LED diode at your electro meter switches on. </WRAP> <WRAP half column> {{  :en:sim:rm:rychly_navod:jak_na_to:obrazek_elmeru.png?100  }} </WRAP>\\
-**Follow  instruction bellow in order to setup a number of pulses different than 1000 per 1 kWh:**
-==== 1. Direct measuring ====
-In the electro meter's label or documentation find out how many pulses per 1 kWh  your electro meter generates at the SO output. Fill in this value into relevant box in SM2-MU menu [[:en:sim:manual:menu_nastaveni:stridace_a_mereni|Invertes and measuring]].\\
-==== 2. Indirect measuring ====
-In the electro meter's label or documentation find out how many pulses per 1 kWh  your electro meter generates at the SO output. Use this number in calculation, see example bellow.\\
-\\
-__Example: Electro meter's label states 10 000 impulses per 1 kWh.__ \\
-\\
-<WRAP half column> Look at the indirect power measuring transformer (1 transformer connected to each phase) and find a ratio (e.g. 150A/5A). Use the result of this ratio (30 in this example) in the formula (10 000/30). Fill in the whole formula (i.e. 10000/30) into relevant box in SM2-MU menu [[:en:sim:manual:menu_nastaveni:stridace_a_mereni|Inverters and measuring]].\\
-\\
-</WRAP> <WRAP half column>\\
-{{  :en:sim:manual:rychly_navod:jak_na_to:impulsy_neprime_mereni.png?200  }} </WRAP>
-<WRAP half column>\\
-\\
-\\
-\\
-\\
-When you have changed the setup, remember to save  the changes {{:en:sim:manual:rychly_navod:jak_na_to:tlacitko_ulozit.png?nolink&}}. </WRAP> <WRAP half column> {{  :en:sim:manual:rychly_navod:jak_na_to:ul_zmeny_strid_a_mereni.png?100  }}</WRAP>
-<WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:konfigurace_stridacu|Next >>]] </WRAP> <WRAP left> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|<< Back]] </WRAP>