en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verzeNásledující verzeObě strany příští revize | ||
en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu [2018/06/27 12:45] – ondra | en:sim:manual:rychly_navod:konfigurace:nastaveni_pulzu [2018/09/14 12:19] – jitka | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
- | ===== How to Setup Reading Pulses from the Electrometer | + | ===== Step 4 - Counter Settings |
Řádek 5: | Řádek 5: | ||
- | In case there is no electro meter connected to your Solar Monitor, go to [[.:konfigurace_stridacu|Next >> | + | If there is no counter |
\\ | \\ | ||
- | <WRAP half column>\\ | + | {{ : |
+ | First you need to enable the chosen input, then you will be able to set it up.\\ | ||
+ | {{ : | ||
+ | Select particular counter.\\ | ||
+ | {{ : | ||
\\ | \\ | ||
- | \\ | + | Click on Next on the right to get to the next step. < |
- | \\ | + | |
- | \\ | + | |
- | In SM2-MU web interface go to menu Settings/ | + | |
- | </ | + | |
- | <WRAP half column> | + | |
- | {{ | + | |
- | </WRAP> | + | |
- | \\ | + | |
- | V tabulce Vstupy a čítače vyberte u toho vstupu, do kterého máte připojené měřidlo, funkci Čítač. | + | |
- | Pozn.: Měřidlo může být připojeno do každého ze tří vstupů. Do SM2-MU tak můžete připojit až 3 měřidla. \\ | + | |
- | {{ : | + | |
- | + | ||
- | <WRAP half column> | + | |
- | In Energy measuring setup select reading energy from the electro meter and set up the right number of pulses per 1 kWh.\\ | + | |
- | </ | + | |
- | </ | + | |
- | \\ | + | |
- | <WRAP half column> | + | |
- | \\ | + | |
- | Enter PV plant' | + | |
- | </ | + | |
- | <WRAP half column> | + | |
- | {{ ..: | + | |
- | \\ | + | |
- | </ | + | |
- | <WRAP info> Default setting is reading 1000 pulses per 1 kWh. If your electro meter shows a different number, change the setting. If it is 1000 pulses, go to [[.: | + | |
- | </ | + | |
- | <WRAP half column> | + | |
- | \\ | + | |
- | The number of impulses per 1 kWh is usually between 250-1000 imp/1kWh. In case there are 2 possible numbers of impulses at your electro meter, the lower number is usually the right one for the SO output.\\ | + | |
- | The higher number tells you how often a LED diode at your electro meter switches on. | + | |
- | </ | + | |
- | <WRAP half column> | + | |
- | {{ .: | + | |
- | \\ \\ | + | |
- | </ | + | |
- | **Follow | + | |
- | ==== 1. Direct measuring ==== | + | |
- | + | ||
- | + | ||
- | In the electro meter' | + | |
- | ==== 2. Indirect measuring ==== | + | |
- | + | ||
- | + | ||
- | In the electro meter' | + | |
- | \\ | + | |
- | __Example: Electro meter' | + | |
- | \\ | + | |
- | <WRAP half column> Look at the indirect power measuring transformer (1 transformer connected to each phase) and find a ratio (e.g. 150A/5A). Use the result of this ratio (30 in this example) in the formula (10 000/30). Fill in the whole formula (i.e. 10000/30) into relevant box in SM2-MU menu [[..:..: | + | |
- | \\ | + | |
- | </ | + | |
- | {{ ..: | + | |
- | + | ||
- | + | ||
- | <WRAP half column> | + | |
- | \\ | + | |
- | \\ | + | |
- | \\ | + | |
- | \\ | + | |
- | When you have changed the setup, remember to save the changes {{..: | + | |
- | + | ||
- | + | ||
- | <WRAP right> [[.: | + | |
- | <WRAP left> [[.:nazev_jednotky|<< Back]] </ | + | |
en/sim/manual/rychly_navod/konfigurace/nastaveni_pulzu.txt · Poslední úprava: 2019/03/11 14:50 autor: ondra