Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.

--- en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2014/07/24 15:37] – jitka
+++ en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2019/02/07 12:19] (aktuální) – link to Utilities (ETool) english page dusan
@@ Řádek 9: / Řádek 9: @@
-In case you don't have DHCP server in your net, connect the unit to the power supply and when green LED diode Status is on, press button Setup 3 times.\\
+In case you don't have DHCP server in your net, for firmware version **2.2.0 Build 51 or higher ** follow these steps:\\
-After a few seconds you can log in at the IP address [[http://192.168.1.99|192.168.1.99]].\\
+. In Solar Monitor press button Setup and keep holding.\\
+. Connect the power supply.\\
+. When power supply has been connected, wait until Status diode starts flashing green light (takes about 5 sec), let go off Setup button and then press it 3 times.\\
+. Within 10 seconds you will be able to connect at the permanent IP address [[http://192.168.1.99|192.168.1.99]].\\
 \\
-When you enter this IP address in your web browser, you display the unit's web interface.\\
+In case your Solar Monitor has firmware version **older than 2.2.0 Build 5up button1**, follow these steps:\\
+Connect the unit to the power supply and when green LED diode Status starts glowing, press Setup button 3 times.\\
+<font 12.8px/arial;;#000000;;#ffffff>Within a few seconds you will be able to connect at the permanent IP addres</font> <font 12.8px/arial;;#000000;;#ffffff>s</font> [[http://192.168.1.99|192.168.1.99]].\\
 \\
-Applikation **ETool ** makes finding SM2-MU in the net easier.**** \\
+When you enter this IP address into your browser, you will find unit's web interface.\\
 \\
-This application identifies your unit without the IP address. You can download the application [[http://www.solarmonitor.cz/podpora/ke-stazeni/utililty|here]] and install in your PC.\\
+Application **ETool** <font 12.8px/arial;;#000000;;#ffffff>makes finding</font> <font 12.8px/arial;;#000000;;#ffffff>SM2-MU on the net easier.</font>\\
+\\
+This application enables finding your unit with any IP address setting. Application to be downloaded [[https://www.solarmonitor.cz/support/download/utilities|here]] and then you can install it in your PC.\\
 \\
 {{  :en:sim:manual:prvni_spusteni:etool.png?nolink&  }}\\
 \\
-Button {{:en:sim:manual:prvni_spusteni:etool_tlacitko.png?nolink&}} next to box “IP address“ opens particular unit's sites. See chapter [[:en:sim:manual:prvni_spusteni:zobrazeni_weboveho_rozhrani|Web interface]].\\
+Button {{:en:sim:manual:prvni_spusteni:etool_tlacitko.png?nolink&}}next to “IP address“ opens website of chosen unit. See chapter [[:en:sim:manual:prvni_spusteni:zobrazeni_weboveho_rozhrani|Web interface]].\\
-Or you can click on button Device image (left down) in order to open  the unit's sites.\\
+Unit's website can also be opened with a click on Device Image.\\
+\\
 \\
 <WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|Next >>]] </WRAP>