en:sim:manual:menu_nastaveni:stridace_a_mereni:ethernet
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verze | ||
en:sim:manual:menu_nastaveni:stridace_a_mereni:ethernet [2014/08/06 15:48] – jitka | en:sim:manual:menu_nastaveni:stridace_a_mereni:ethernet [2018/06/11 09:30] (aktuální) – ondra | ||
---|---|---|---|
Řádek 9: | Řádek 9: | ||
\\ | \\ | ||
\\ | \\ | ||
- | To be set up in the submenu | + | To be set up in the submenu |
</ | </ | ||
<WRAP half column> | <WRAP half column> | ||
\\ | \\ | ||
- | Select the manufacturer of your inverter. </ | + | Select the manufacturer of your inverter. </ |
\\ | \\ | ||
<WRAP info> Setting up network interface has two address modes: | <WRAP info> Setting up network interface has two address modes: | ||
- | 1. IP Address\\ | + | 1. IP Address |
- | 2. Port\\ | + | 2. Port - remote communication via public IP address of router with translation of addresses (NAT) \\ |
</ | </ | ||
==== IP Address Detection of Inverters ==== | ==== IP Address Detection of Inverters ==== | ||
- | Use this type of detection | + | Use this type of detection |
\\ | \\ | ||
<WRAP info> Address the inverters first. Assign consequent IP addresses to the inverters and the port number. The port number is the same for all inverters. Further info on how to address the inverters to be found in inverter' | <WRAP info> Address the inverters first. Assign consequent IP addresses to the inverters and the port number. The port number is the same for all inverters. Further info on how to address the inverters to be found in inverter' | ||
Řádek 29: | Řádek 29: | ||
Enter inverter with the lowest IP address in the network. Detection starts with this address and searches for following higher IP addresses until the required number of destinations has been searched.\\ | Enter inverter with the lowest IP address in the network. Detection starts with this address and searches for following higher IP addresses until the required number of destinations has been searched.\\ | ||
\\ | \\ | ||
- | {{ | + | {{ |
Enter port's number.\\ | Enter port's number.\\ | ||
\\ | \\ | ||
Řádek 42: | Řádek 42: | ||
\\ | \\ | ||
**Read Connected Inverters** \\ | **Read Connected Inverters** \\ | ||
- | Click on button{{:en: | + | Click on button {{..:..: |
\\ | \\ | ||
- | Detection can take up to several minutes depending on the type of protocol and the number of inverters. <WRAP info> To be detected, inverters must be on, i.e. they must have sufficient electric current coming from the PV panels. </ | + | Detection can take up to several minutes depending on the type of protocol and the number of inverters. <WRAP info> To be detected, inverters must be on, i.e. they must have sufficient electric current coming from the PV panels. </ |
- | \\ | + | Save changes you have made{{..:..: |
- | \\ | + | For detailed info on inverter' |
- | \\ | + | |
- | \\ | + | |
- | Save changes you have made{{:en: | + | |
- | \\ | + | |
- | </ | + | |
\\ | \\ | ||
==== Port Detection of Inverters ==== | ==== Port Detection of Inverters ==== | ||
- | Use this type of detection | + | Select |
\\ | \\ | ||
- | <WRAP info> Address the inverters first. Assign | + | <WRAP info> Address the inverters first. Assign |
\\ | \\ | ||
**IP address** \\ | **IP address** \\ | ||
- | Enter IP address, the same address | + | Enter the public |
\\ | \\ | ||
- | {{ | + | {{ |
Enter inverter with the lowest port number (destination) at a particular IP address. Detection starts with this port and searches for following higher port numbers until the required number of destinations has been searched.\\ | Enter inverter with the lowest port number (destination) at a particular IP address. Detection starts with this port and searches for following higher port numbers until the required number of destinations has been searched.\\ | ||
\\ | \\ | ||
Řádek 76: | Řádek 71: | ||
\\ | \\ | ||
\\ | \\ | ||
- | Read connected inverters**\\ | + | **Read connected inverters**\\ |
- | Click on button{{:en: | + | Click on button{{..:..: |
- | \\ | + | |
- | Detection can take up to several minutes depending on the type of protocol and the number of inverters. <WRAP info> To be detected, inverters must be on, i.e. they must have sufficient electric current coming from the PV panels. </ | + | |
- | \\ | + | |
- | \\ | + | |
- | \\ | + | |
- | \\ | + | |
- | Save the changes you have made {{: | + | |
\\ | \\ | ||
- | </ | + | Detection can take up to several minutes depending on the type of protocol and the number of inverters. <WRAP info> To be detected, inverters must be on, i.e. they must have sufficient electric current coming from the PV panels. |
+ | Save the changes you have made {{..: | ||
+ | For detailed info on inverter' | ||
en/sim/manual/menu_nastaveni/stridace_a_mereni/ethernet.1407332924.txt.gz · Poslední úprava: 2014/08/06 15:48 autor: jitka