en:sim:manual:menu_nastaveni:vstupy_a_vystupy
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verze | ||
en:sim:manual:menu_nastaveni:vstupy_a_vystupy [2018/06/08 10:59] – ondra | en:sim:manual:menu_nastaveni:vstupy_a_vystupy [2019/03/01 12:01] (aktuální) – ondra | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
===== Inputs & Counters ===== | ===== Inputs & Counters ===== | ||
+ | |||
+ | |||
---- | ---- | ||
- | Submenu Inputs | + | |
- | Výchozí nastavení tabulky | + | |
- | {{ .: | + | Submenu Inputs |
- | ==== Nastavení vstupů ==== | + | \\ |
- | **Zvolte funkci vstupu** \\ | + | Default setting of the chart\\ |
- | Solar Monitor | + | {{ : |
- | === a) Vstup = binární vstup === | + | |
- | V tabulce jsou uvedeny současné stavy vstupů. Nastavte jejich povolenou hodnotu. \\ | + | |
- | {{ .: | + | **Select input function** \\ |
- | Vyberte, zda si chcete nechat poslat hlášení | + | Solar Monitor |
- | === b) Čítač | + | |
- | {{ .: | + | |
- | Po zvolení funkce Čítač se nad tabulkou vstupů zobrazí tabulka nastavení čítače. \\ | + | ==== a) Input = binary input ==== |
- | {{ .: | + | |
- | Více informací o nastavení počtu pulzů naleznete v kapitole o [[..: | + | |
- | V případě zadání chybné hodnoty bude Solar Monitor zobrazovat špatné údaje o vyrobené energii. | + | This chart presents current input status. Set up allowed value for them.\\ |
- | \\ | + | {{ : |
- | <WRAP info> | + | Choose if you want to receive report |
- | Pokud se pulsy nečítají, zkontrolujte vedení | + | |
- | </ | + | |
- | \\ | + | ==== b) Counter |
- | === c) Vstup a Čítač | + | |
- | {{ .: | + | |
- | Po zvolení funkce Vstup a Čítač se nad tabulkou vstupů zobrazí tabulka nastavení čítače. \\ | + | In the chart Inputs and Counters select function Counter for the particular input where meter is connected.\\ |
- | {{ .: | + | <WRAP info> Meter can be connected to any of the 3 inputs. There can be up to 3 meters at each SM2-MU. </ |
- | Pokud využíváte tento vstup také jako binární, nastavte jeho povolenou hodnotu | + | After you have chosen function Counter, its setup chart appears.\\ |
+ | {{ : | ||
+ | Enter its name (e.g. electrometer) and select its type.\\ | ||
+ | Enter the correct number of pulses per 1 kWh (as specified in SO output at the counter).\\ | ||
+ | <WRAP info> | ||
+ | Number of pulses per 1 kWh is normally between 250-1000 imp/1kWh. If your electrometer has two numbers of pulses, the right SO output number is usually the lower one.\\ | ||
+ | Higher number says how many times light diode at the electrometer flashes. </ | ||
+ | \\ | ||
+ | </ | ||
+ | === For direct measurement === | ||
+ | |||
+ | |||
+ | Find out how many pulses per kWh does your electrometer generate at SO output. This information is available at the label or in its documentation. Enter this number into the box Pulses Count in SM2-MU. | ||
+ | |||
+ | |||
+ | === For indirect measurement === | ||
+ | |||
+ | |||
+ | <font 12.8px/ | ||
+ | \\ | ||
+ | __Example: Electrometer specification says there is 10 000 pulses per 1 kWh.__ \\ | ||
+ | \\ | ||
+ | <WRAP half column> Check transformer of indirect power measurement which is connected to electrometer (each phase one transformer). You should find a ratio (e.g. 150A/5A). Calculate the ratio (150:5=30 in this example). Use the result number (30 in this case) in this formula 10 000/30. Enter this number into the box Pulse Count.\\ | ||
+ | \\ | ||
+ | </ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | </ | ||
+ | |||
+ | |||
+ | ==== c) Input and Counter | ||
+ | |||
+ | |||
+ | {{ : | ||
+ | After you have chosen function Input and Counter, | ||
+ | If there is e.g. inverter production selected, there will be total sum of all detected inverters in Production summary.\\ | ||
+ | {{ : | ||
+ | In case you use this input as binary, set up its allowed value.\\ | ||
+ | \\ | ||
+ | After each change in settings, don't forget to press button {{: |
en/sim/manual/menu_nastaveni/vstupy_a_vystupy.1528448354.txt.gz · Poslední úprava: 2018/06/08 10:59 autor: ondra