en:sim:manual:prvni_spusteni:vyhledani_jednotky_v_siti_a_pripojeni
no way to compare when less than two revisions
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Předchozí verzeNásledující verze | |||
— | en:sim:manual:prvni_spusteni:vyhledani_jednotky_v_siti_a_pripojeni [2013/12/12 09:59] – jitka | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
+ | ===== How to find and connect unit in the LAN ===== | ||
+ | |||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | \\ | ||
+ | When you have switched on the power supply a green LED diode indicating status lights up. At the same time a green diode at the net connector lights up and an orange diode starts flashing . | ||
+ | |||
+ | |||
+ | ==== Getting IP address ==== | ||
+ | |||
+ | |||
+ | \\ | ||
+ | With nets TCP/IP (most common ones currently) every item needs its setting: | ||
+ | |||
+ | |||
+ | * **IP address** | ||
+ | * **Network mask** | ||
+ | * **Default gateway** | ||
+ | * **DNS servers** | ||
+ | Once you have connected Solar Monitor unit to the local network or to your PC (see chapter [[: | ||
+ | |||
+ | |||
+ | * If you want to connect Solar Monitor unit to the company network, consult the network administrator fist. | ||
+ | * If you want to connect Solar Monitor unit to your domestic network, it is very likely that there is a DHCP server which assigns the newly connected devices correct setting automatically. | ||
+ | * If you want to connect Solar Monitor unit to the PC directly, see the chapter bellow: Connecting to the PC directly. | ||
+ | |||
+ | |||
+ | <WRAP info> For initial connection with the unit we only to need set up the IP address and Network mask correctly. It means that your PC and the unit are in the same network. The same network = different IP address (e.g. 192.168.1.99 and 192.168.1.98) but the same network mask. </ | ||
+ | |||
+ | |||
+ | If there is no DHCP server in your network, connect the unit to the power supply and when the green LED diode Status lights up, press button Setup three times. in few seconds you will be able to connect to fixed IP address 192.168.1.99. | ||
+ | |||
+ | |||
+ | To find the unit in the net there is application Etool available (download here[[http:// | ||
+ | | ||
+ | {{ : | ||
+ | | ||
+ | The list shows all Solar Monitor devices connected to the local network. Newly detected devices are highlighted in blue colour. <WRAP info> If Solar Monitor unit has DHCP client regime granted ( in default setting yes!) it comes up in the list after certain delay set for DHCP server' | ||
+ | Button {{: | ||
+ | |||
+ | |||
+ | ==== Direct connection to your PC ==== | ||
+ | |||
+ | |||
+ | In case your unit is connected directly to the PC/laptop it is not possible to to contact DHCP server. After the delay of 60 seconds the unit uses this default set up: \\ \\ Table of network default setting values (IP configuration) in Solar Monitor | ||
+ | |||
+ | |||
+ | ^ Parameter | ||
+ | | IP address | ||
+ | | Network mask | 255.255.255.0 | ||
+ | | Default gateway | ||
+ | | DNS1, DNS2 | 0.0.0.0, 0.0.0.0 | ||
+ | |||
+ | |||
+ | | ||
+ | |||
+ | |||
+ | ^ Parameter | ||
+ | | IP address | ||
+ | | Network mask | 255.255.0.0 | ||
+ | | Default gateway | ||
+ | | DNS1, DNS2 | 0.0.0.0, 0.0.0.0 | ||
+ | |||
+ | |||
+ | In order to enable communication with Solar Monitor unit set the IP address of your PC at 192.168.1.98 and network mask at 255.255.255.0. The settings are available in control panels. | ||
+ | |||
+ | |||
+ | | ||
+ | |||
+ | |||
+ | ^ Parameter | ||
+ | | IP address | ||
+ | | Network mask | 255.255.255.0 | ||
+ | | Default gateway | ||
+ | | DNS1, DNS2 | 0.0.0.0, 0.0.0.0 | ||
+ | |||
+ | |||
+ | \\ | ||
en/sim/manual/prvni_spusteni/vyhledani_jednotky_v_siti_a_pripojeni.txt · Poslední úprava: 2020/01/15 10:09 autor: ondra