en:sim:manual:rychly_navod:jak_na_to:senzory
Differences
This shows you the differences between two versions of the page.
|
en:sim:manual:rychly_navod:jak_na_to:senzory [2014/08/15 16:00] jitka |
en:sim:manual:rychly_navod:jak_na_to:senzory [2019/08/19 12:44] (current) ondra |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| - | If there are no sensors connected to your SM2-MU device, go to [[:en:sim:manual:rychly_navod:jak_na_to:stridace|Next >>]]\\ | + | If there are no sensors connected to your SM2-MU device, go to [[.:stridace|Next >>]]\\ |
| \\ | \\ | ||
| <WRAP half column>\\ | <WRAP half column>\\ | ||
| Line 12: | Line 12: | ||
| Connect the sensors to the SM2-MU according to the following pictures:\\ | Connect the sensors to the SM2-MU according to the following pictures:\\ | ||
| \\ | \\ | ||
| - | </WRAP> <WRAP half column> {{ :en:sim:manual:rychly_navod:jak_na_to:senzory_svorky.png?nolink&250 }}\\ | + | </WRAP> <WRAP half column> {{ .:senzory_svorky.png?nolink&250 }}\\ |
| \\ | \\ | ||
| </WRAP> | </WRAP> | ||
| Line 18: | Line 18: | ||
| ==== Irradiation Sensor ==== | ==== Irradiation Sensor ==== | ||
| - | + | \\ | |
| + | In this picture you see to which terminal on the SM2-MU connects each pin of the irradiance sensor. \\ \\ | ||
| + | {{.:osvit_piny_en.png?&250 |}} \\ \\ | ||
| <WRAP half column>\\ | <WRAP half column>\\ | ||
| \\ | \\ | ||
| \\ | \\ | ||
| - | To be connected with 10 meters cable with pressed-in connector. Connect the cable to SM2-MU terminals and the pressed-in connector to the irradiation sensor. </WRAP> <WRAP half column> {{ :en:sim:manual:rychly_navod:jak_na_to:osvit.png?nolink&250 }}\\ | + | To be connected with 10 meters cable with pressed-in connector. Connect the cable to SM2-MU terminals and the pressed-in connector to the irradiation sensor. </WRAP> <WRAP half column> {{ .:osvit.png?nolink&250 }}\\ |
| \\ | \\ | ||
| </WRAP>\\ | </WRAP>\\ | ||
| Line 31: | Line 32: | ||
| \\ | \\ | ||
| </WRAP> <WRAP half column>\\ | </WRAP> <WRAP half column>\\ | ||
| - | {{ :en:sim:manual:rychly_navod:jak_na_to:m8f_konektor.png?nolink&120 }}\\ | + | {{ .:m8f_konektor.png?nolink&120 }}\\ |
| \\ | \\ | ||
| </WRAP> <WRAP half column>\\ | </WRAP> <WRAP half column>\\ | ||
| \\ | \\ | ||
| - | 2. Connect the PUR cable to SM2-MU terminals and the M8F connector to the irradiation sensor. </WRAP> <WRAP half column> {{ :en:sim:manual:rychly_navod:jak_na_to:osvit_2.png?nolink&260 }}\\ | + | 2. Connect the PUR cable to SM2-MU terminals and the M8F connector to the irradiation sensor. </WRAP> <WRAP half column> {{ .:osvit_2.png?nolink&260 }}\\ |
| \\ | \\ | ||
| </WRAP> | </WRAP> | ||
| Line 46: | Line 47: | ||
| \\ | \\ | ||
| \\ | \\ | ||
| - | Connect the pressed-in connector of PV panel sensor cable to the irradiation sensor. </WRAP> <WRAP half column> {{ :en:sim:manual:rychly_navod:jak_na_to:senzor_fv_panelu.png?nolink&250 }}\\ | + | Connect the pressed-in connector of PV panel sensor cable to the irradiation sensor. </WRAP> <WRAP half column> {{ .:senzor_fv_panelu.png?nolink&250 }}\\ |
| \\ | \\ | ||
| </WRAP> | </WRAP> | ||
| Line 56: | Line 57: | ||
| <WRAP half column>\\ | <WRAP half column>\\ | ||
| \\ | \\ | ||
| + | \\ | ||
| + | \\ | ||
| + | \\ | ||
| + | \\ | ||
| + | \\ | ||
| \\ | \\ | ||
| - | Connect blue silicone cable to the SM2-MU terminals. </WRAP> <WRAP half column> {{ :en:sim:manual:rychly_navod:jak_na_to:senzor_okoli.png?nolink&250 }}\\ | + | \\ |
| + | Connect blue or brown silicone cable to the SM2-MU terminals. </WRAP> | ||
| + | <WRAP half column> {{ .:senzor_okoli.png?nolink&250 }} | ||
| \\ | \\ | ||
| + | \\ | ||
| + | {{ .:senzor_okoli_hnedy_en.png?direct&250 |}} | ||
| </WRAP>\\ | </WRAP>\\ | ||
| \\ | \\ | ||
| - | Solar Monitor can operate up to 10 sensors. The total length of cabling must not exceed 100 meters. In case of multiple sensors connect each cable parallelly into the same terminals.\\ | + | Solar Monitor can operate up to 10 sensors. The total length of cabling must not exceed 100 meters. In case of multiple sensors connect each cable parallelly into the same terminals.\\ \\ |
| + | You can find several connection schemes of sensors [[..:jak_na_to:senzory:priklady_zapojeni|here]]. | ||
| \\ | \\ | ||
| - | <WRAP right> [[:en:sim:manual:rychly_navod:jak_na_to:stridace|Dext >>]] </WRAP> <WRAP left> [[:en:sim:manual:rychly_navod:jak_na_to:montaz|<< Previous]] </WRAP> | + | <WRAP right> [[.:stridace|Next >>]] </WRAP> <WRAP left> [[.:montaz|<< Previous]] </WRAP> |
en/sim/manual/rychly_navod/jak_na_to/senzory.1408111227.txt.gz · Last modified: 2014/08/15 16:00 by jitka
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
