This shows you the differences between two versions of the page.
en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2014/03/13 09:12] 127.0.0.1 external edit |
en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2019/02/07 12:19] (current) dusan link to Utilities (ETool) english page |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Vyhledání jednotky v síti a zobrazení webového rozhraní ===== | + | ===== Finding the Unit in the Net, Web Interface Display ===== |
+ | |||
---- | ---- | ||
- | \\ | ||
- | Jednotka SM2-MU má v továrním nastavení povolen režim DHCP klient - IP adresu získá automaticky od DHCP serveru v místní síti (pokud je dostupný). | ||
- | V případě, že nemáte DHCP server ve Vaší síti, připojte jednotku k napájení a jakmile se rozsvítí zelená LED dioda Status, stiskněte 3x tlačítko Setup. \\ | + | |
- | Po několika vteřinách je možno se připojit na pevné IP adrese [[http://192.168.1.99|192.168.1.99]]. \\ \\ | + | \\ |
- | Zadáním této IP adresy do Vašeho internetového prohlížeče zobrazíte webové rozhraní jednotky. \\ \\ | + | SM2-MU unit allows DHCP client regime in the default setting. The IP address is allocated automatically by the DHCP server in local net (if available). |
- | Pro usnadnění vyhledávání SM2-MU na síti slouží aplikace **ETool**. \\ \\ | + | |
- | Tato aplikace nalezne Vaši jednotku nezávisle na nastavení IP adres. Aplikaci si můžete stáhnout [[http://www.solarmonitor.cz/podpora/ke-stazeni/utililty|zde]] a poté nainstalovat do Vašeho PC. \\ \\ | + | |
- | {{ ..:..:prvni_spusteni:etool.png?nolink |}} \\ \\ | + | In case you don't have DHCP server in your net, for firmware version **2.2.0 Build 51 or higher ** follow these steps:\\ |
- | Tlačítko {{..:..:prvni_spusteni:etool_tlacitko.png?nolink|}} vedle pole “IP adresa“ otevře stránky vybrané jednotky. Viz kapitola [[..:..:prvni_spusteni:zobrazeni_weboveho_rozhrani|Webové rozhraní]]. \\ | + | 1. In Solar Monitor press button Setup and keep holding.\\ |
- | Stránky jednotky lze taktéž otevřít vlevo dole proklikem přes Obrázek zařízení. \\ \\ | + | 2. Connect the power supply.\\ |
- | <WRAP right> | + | 3. When power supply has been connected, wait until Status diode starts flashing green light (takes about 5 sec), let go off Setup button and then press it 3 times.\\ |
- | [[.:nazev_jednotky|Další >>]] | + | 4. Within 10 seconds you will be able to connect at the permanent IP address [[http://192.168.1.99|192.168.1.99]].\\ |
- | </WRAP> | + | \\ |
+ | In case your Solar Monitor has firmware version **older than 2.2.0 Build 5up button1**, follow these steps:\\ | ||
+ | Connect the unit to the power supply and when green LED diode Status starts glowing, press Setup button 3 times.\\ | ||
+ | <font 12.8px/arial;;#000000;;#ffffff>Within a few seconds you will be able to connect at the permanent IP addres</font> <font 12.8px/arial;;#000000;;#ffffff>s</font> [[http://192.168.1.99|192.168.1.99]].\\ | ||
+ | \\ | ||
+ | When you enter this IP address into your browser, you will find unit's web interface.\\ | ||
+ | \\ | ||
+ | Application **ETool** <font 12.8px/arial;;#000000;;#ffffff>makes finding</font> <font 12.8px/arial;;#000000;;#ffffff>SM2-MU on the net easier.</font>\\ | ||
+ | \\ | ||
+ | This application enables finding your unit with any IP address setting. Application to be downloaded [[https://www.solarmonitor.cz/support/download/utilities|here]] and then you can install it in your PC.\\ | ||
+ | \\ | ||
+ | {{ :en:sim:manual:prvni_spusteni:etool.png?nolink& }}\\ | ||
+ | \\ | ||
+ | Button {{:en:sim:manual:prvni_spusteni:etool_tlacitko.png?nolink&}}next to “IP address“ opens website of chosen unit. See chapter [[:en:sim:manual:prvni_spusteni:zobrazeni_weboveho_rozhrani|Web interface]].\\ | ||
+ | Unit's website can also be opened with a click on Device Image.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | <WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|Next >>]] </WRAP> |