This shows you the differences between two versions of the page.
en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2014/07/24 15:37] jitka |
en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2019/02/07 12:19] (current) dusan link to Utilities (ETool) english page |
||
---|---|---|---|
Line 9: | Line 9: | ||
- | In case you don't have DHCP server in your net, connect the unit to the power supply and when green LED diode Status is on, press button Setup 3 times.\\ | + | In case you don't have DHCP server in your net, for firmware version **2.2.0 Build 51 or higher ** follow these steps:\\ |
- | After a few seconds you can log in at the IP address [[http://192.168.1.99|192.168.1.99]].\\ | + | 1. In Solar Monitor press button Setup and keep holding.\\ |
+ | 2. Connect the power supply.\\ | ||
+ | 3. When power supply has been connected, wait until Status diode starts flashing green light (takes about 5 sec), let go off Setup button and then press it 3 times.\\ | ||
+ | 4. Within 10 seconds you will be able to connect at the permanent IP address [[http://192.168.1.99|192.168.1.99]].\\ | ||
\\ | \\ | ||
- | When you enter this IP address in your web browser, you display the unit's web interface.\\ | + | In case your Solar Monitor has firmware version **older than 2.2.0 Build 5up button1**, follow these steps:\\ |
+ | Connect the unit to the power supply and when green LED diode Status starts glowing, press Setup button 3 times.\\ | ||
+ | <font 12.8px/arial;;#000000;;#ffffff>Within a few seconds you will be able to connect at the permanent IP addres</font> <font 12.8px/arial;;#000000;;#ffffff>s</font> [[http://192.168.1.99|192.168.1.99]].\\ | ||
\\ | \\ | ||
- | Applikation **ETool ** makes finding SM2-MU in the net easier.**** \\ | + | When you enter this IP address into your browser, you will find unit's web interface.\\ |
\\ | \\ | ||
- | This application identifies your unit without the IP address. You can download the application [[http://www.solarmonitor.cz/podpora/ke-stazeni/utililty|here]] and install in your PC.\\ | + | Application **ETool** <font 12.8px/arial;;#000000;;#ffffff>makes finding</font> <font 12.8px/arial;;#000000;;#ffffff>SM2-MU on the net easier.</font>\\ |
+ | \\ | ||
+ | This application enables finding your unit with any IP address setting. Application to be downloaded [[https://www.solarmonitor.cz/support/download/utilities|here]] and then you can install it in your PC.\\ | ||
\\ | \\ | ||
{{ :en:sim:manual:prvni_spusteni:etool.png?nolink& }}\\ | {{ :en:sim:manual:prvni_spusteni:etool.png?nolink& }}\\ | ||
\\ | \\ | ||
- | Button {{:en:sim:manual:prvni_spusteni:etool_tlacitko.png?nolink&}} next to box “IP address“ opens particular unit's sites. See chapter [[:en:sim:manual:prvni_spusteni:zobrazeni_weboveho_rozhrani|Web interface]].\\ | + | Button {{:en:sim:manual:prvni_spusteni:etool_tlacitko.png?nolink&}}next to “IP address“ opens website of chosen unit. See chapter [[:en:sim:manual:prvni_spusteni:zobrazeni_weboveho_rozhrani|Web interface]].\\ |
- | Or you can click on button Device image (left down) in order to open the unit's sites.\\ | + | Unit's website can also be opened with a click on Device Image.\\ |
+ | \\ | ||
\\ | \\ | ||
<WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|Next >>]] </WRAP> | <WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|Next >>]] </WRAP> | ||