This shows you the differences between two versions of the page.
en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2018/08/27 13:24] ondra |
en:sim:manual:rychly_navod:konfigurace:vyhledani_v_siti [2019/02/07 12:19] (current) dusan link to Utilities (ETool) english page |
||
---|---|---|---|
Line 9: | Line 9: | ||
- | V případě, že nemáte DHCP server ve Vaší síti, pro verzi firmware verze **2.2.0 Build 51 nebo vyšší** postupujte takto: \\ | + | In case you don't have DHCP server in your net, for firmware version **2.2.0 Build 51 or higher ** follow these steps:\\ |
- | 1. Stiskněte na Solar Monitoru tlačítko Setup a držte ho. \\ | + | 1. In Solar Monitor press button Setup and keep holding.\\ |
- | 2. Připojte napájení. \\ | + | 2. Connect the power supply.\\ |
- | 3. Po připojení napájení vyčkejte cca 5 sekund až začne dioda Status zeleně blikat, pusťte tlačítko Setup a poté ho 3x stiskněte. \\ | + | 3. When power supply has been connected, wait until Status diode starts flashing green light (takes about 5 sec), let go off Setup button and then press it 3 times.\\ |
- | 4. Do 10 sekund je možno se připojit na pevné IP adrese [[http://192.168.1.99|192.168.1.99]]. \\ | + | 4. Within 10 seconds you will be able to connect at the permanent IP address [[http://192.168.1.99|192.168.1.99]].\\ |
- | \\ | + | \\ |
- | V případě, že má Solar Monitor verzi firmware **starší než 2.2.0 Build 51**, postupujte takto: \\ | + | In case your Solar Monitor has firmware version **older than 2.2.0 Build 5up button1**, follow these steps:\\ |
- | Připojte jednotku k napájení a jakmile se rozsvítí zelená LED dioda Status, stiskněte 3x tlačítko Setup. \\ | + | Connect the unit to the power supply and when green LED diode Status starts glowing, press Setup button 3 times.\\ |
- | Po několika vteřinách je možno se připojit na pevné IP adrese [[http://192.168.1.99|192.168.1.99]]. \\ \\ | + | <font 12.8px/arial;;#000000;;#ffffff>Within a few seconds you will be able to connect at the permanent IP addres</font> <font 12.8px/arial;;#000000;;#ffffff>s</font> [[http://192.168.1.99|192.168.1.99]].\\ |
- | Zadáním této IP adresy do Vašeho internetového prohlížeče zobrazíte webové rozhraní jednotky. \\ \\ | + | \\ |
- | Pro usnadnění vyhledávání SM2-MU na síti slouží aplikace **ETool**. \\ \\ | + | When you enter this IP address into your browser, you will find unit's web interface.\\ |
- | Tato aplikace nalezne Vaši jednotku nezávisle na nastavení IP adres. Aplikaci si můžete stáhnout [[http://www.solarmonitor.cz/cz/podpora/ke-stazeni/utility|zde]] a poté nainstalovat do Vašeho PC. \\ \\ | + | \\ |
- | {{ ..:..:prvni_spusteni:etool.png?nolink |}} \\ \\ | + | Application **ETool** <font 12.8px/arial;;#000000;;#ffffff>makes finding</font> <font 12.8px/arial;;#000000;;#ffffff>SM2-MU on the net easier.</font>\\ |
- | Tlačítko {{..:..:prvni_spusteni:etool_tlacitko.png?nolink|}} vedle pole “IP adresa“ otevře stránky vybrané jednotky. Viz kapitola [[..:..:prvni_spusteni:zobrazeni_weboveho_rozhrani|Webové rozhraní]]. \\ | + | \\ |
- | Stránky jednotky lze taktéž otevřít vlevo dole proklikem přes Obrázek zařízení. \\ \\ | + | This application enables finding your unit with any IP address setting. Application to be downloaded [[https://www.solarmonitor.cz/support/download/utilities|here]] and then you can install it in your PC.\\ |
+ | \\ | ||
+ | {{ :en:sim:manual:prvni_spusteni:etool.png?nolink& }}\\ | ||
+ | \\ | ||
+ | Button {{:en:sim:manual:prvni_spusteni:etool_tlacitko.png?nolink&}}next to “IP address“ opens website of chosen unit. See chapter [[:en:sim:manual:prvni_spusteni:zobrazeni_weboveho_rozhrani|Web interface]].\\ | ||
+ | Unit's website can also be opened with a click on Device Image.\\ | ||
+ | \\ | ||
\\ | \\ | ||
<WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|Next >>]] </WRAP> | <WRAP right> [[:en:sim:manual:rychly_navod:konfigurace:nazev_jednotky|Next >>]] </WRAP> | ||