en:sim:manual:rozsirujici_moduly:sm2_ad:vstupy_a_vystupy
Differences
This shows you the differences between two versions of the page.
|
en:sim:manual:rozsirujici_moduly:sm2_ad:vstupy_a_vystupy [2014/08/06 16:45] jitka |
en:sim:manual:rozsirujici_moduly:sm2_ad:vstupy_a_vystupy [2014/08/26 14:53] (current) ondra |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| - | Module installation to be found [[:en:sim:manual:rozsirujici_moduly:instalace|here >>]]\\ | + | Module installation to be found [[..:..:rozsirujici_moduly:instalace|here >>]]\\ |
| \\ | \\ | ||
| \\ | \\ | ||
| Line 14: | Line 14: | ||
| 0 - 20 mA, 0 - 10 V, 0 - 20mV, 0 - 100 mV are available for voltage or current measuring.\\ | 0 - 20 mA, 0 - 10 V, 0 - 20mV, 0 - 100 mV are available for voltage or current measuring.\\ | ||
| \\ | \\ | ||
| - | Measurement ranges are set up before module is delivered! Correct specification when you order SM2-AD module is essential. It is possible to connect pyranometer (measures solar irradiation), anemometer (measures wind speed) or battery.\\ | + | Measurement ranges are set up before module is delivered! Correct specification when you order SM2-AD module is essential. It is possible to connect pyranometer (measures solar irradiation), anemometer (measures wind speed) or battery.\\ |
| \\ | \\ | ||
| - | {{ :en:sim:manual:rozsirujici_moduly:ad-analogove_vstupy.png?nolink&400 }}\\ | + | {{ ..:..:rozsirujici_moduly:ad-analogove_vstupy.png?nolink&400 }}\\ |
| \\ | \\ | ||
| Analog output A0 to be connected in the same way. Voltage of 0-10V is detected at output terminals depending on current production or temperature. It can be used for continuous regulation of appliances, e.g. ventilation fan.\\ | Analog output A0 to be connected in the same way. Voltage of 0-10V is detected at output terminals depending on current production or temperature. It can be used for continuous regulation of appliances, e.g. ventilation fan.\\ | ||
| \\ | \\ | ||
| - | {{ :en:sim:manual:rozsirujici_moduly:ad-analogovy_vystup.png?nolink&300 }}\\ | + | {{ ..:..:rozsirujici_moduly:ad-analogovy_vystup.png?nolink&300 }}\\ |
| \\ | \\ | ||
| - | Digitální (relé) výstupy DO připojíme obdobně jako u SM2-MU. Tedy např. k boileru nebo akumulačním kamnům dle obrázku.\\ | + | Digital (relay) outputs DO to be connected in the same way as with SM2-MU. E.g. to the boiler or storage heater as shown in the picture.\\ |
| \\ | \\ | ||
| - | {{ :en:sim:manual:rozsirujici_moduly:ad-digitalni_vystupy.png?nolink&500 }}\\ | + | {{ ..:..:rozsirujici_moduly:ad-digitalni_vystupy.png?nolink&500 }}\\ |
| \\ | \\ | ||
| - | <WRAP right> [[:en:sim:manual:rozsirujici_moduly:sm2_ad:spusteni_konfigurace|Další >>]] </WRAP> <WRAP left> [[:en:sim:manual:rozsirujici_moduly:sm2_ad:parametry|<< Zpět]] </WRAP> | + | <WRAP right> [[.:spusteni_konfigurace|Next >>]] </WRAP> <WRAP left> [[.:parametry|<< Back]] </WRAP> |
en/sim/manual/rozsirujici_moduly/sm2_ad/vstupy_a_vystupy.1407336345.txt.gz · Last modified: 2014/08/06 16:45 by jitka
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
