User Tools

Site Tools

Trace: • vstupy_a_vystupy

Sidebar

Solar Monitor User Guide

  1. Quick Setup
    1. Installation
      1. Sensors
        1. Examples of sensor connection diagrams
          1. Example 1
          2. Example 2
          3. Example 3
      2. Inverters
      3. Electrometer
      4. LAN
      5. Digital Inputs
      6. Digital Outputs
      7. Power Supply
    2. Setup Wizard
      1. General Settings
      2. Interface Settings
      3. Sensor detection
      4. Counter Settings
      5. Emails & SMS
      6. Portal Setup
      7. Date & Time
      8. Summary
  2. Overview
    1. Basic features
    2. Parameters
    3. Safety Warning
    4. Interface Description
  3. How to Install?
    1. Mechanical Fastening
    2. Sensors
    3. Inverters
    4. Electrometer
    5. LAN
    6. Digital inputs and outputs
    7. Plugging a power source
  4. Quick Start
    1. Unit discovery in a LAN
    2. Web interface
  5. Factory Reset
    1. How to factory reset?
  6. Web
    1. Overview
      1. Peaks
      2. LCD Panel
    2. Graphs
    3. Alerts
      1. System Log
      2. Power Control Log
      3. Sending History
    4. Settings
      1. Network & Time
      2. Portal
      3. Email & SMS
      4. GSM / GPRS
      5. SNMP
      6. Modbus
      7. Sensors & Alerts
      8. Find Devices
        1. RS 485
        2. RS 232
        3. Ethernet
      9. Inputs & Counters
      10. Outputs
      11. Power Control
      12. HBUS Modules
      13. Backup, CSV, FW
  7. Extension Modules
    1. Installation
    2. SM2-AD
      1. Module Parameters
      2. SM2-AD Installation
      3. Setup
      4. AI Setup
      5. AO Setup
      6. DO Setup
      7. More SM2-AD?
    3. SM2-BE
    4. SM2-DI
    5. SM2-GSM
    6. SM2-PC
en:sim:manual:rozsirujici_moduly:sm2_ad:vstupy_a_vystupy

Installation, Connecting Inputs and Outputs

Module installation to be found here >>


With analog inputs AI1 and AI2 the ranges of:
0 - 20 mA a 0 - 10 V are available for voltage or current measuring.

With analog input AI3 the ranges of:
0 - 20 mA, 0 - 10 V, 0 - 20mV, 0 - 100 mV are available for voltage or current measuring.

Measurement ranges are set up before module is delivered! Correct specification when you order SM2-AD module is essential. It is possible to connect pyranometer (measures solar irradiation), anemometer (measures wind speed) or battery.



Analog output A0 to be connected in the same way. Voltage of 0-10V is detected at output terminals depending on current production or temperature. It can be used for continuous regulation of appliances, e.g. ventilation fan.



Digital (relay) outputs DO to be connected in the same way as with SM2-MU. E.g. to the boiler or storage heater as shown in the picture.



Next >>

<< Back

en/sim/manual/rozsirujici_moduly/sm2_ad/vstupy_a_vystupy.txt · Last modified: 2014/08/26 14:53 by ondra

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
CC Attribution-Noncommercial-Share Alike 3.0 Unported Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki